Starrett 5004 Depth Gage Uživatelský manuál Strana 2

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 2
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 1
2 3
Operating Instructions
On/Off
AquickpressofeithertheMODEorSETbuttonwillactivethedisplay.Toturnthe
displayoff,pressandholdtheSETbuttonfor2seconds.
Mode Button
This button toggles the display through the selection of a variety of functions.
SET Mode
WhileinthismodeaquickpressoftheSETbuttonwillzerothedisplayorsetittothe
datum value established in the preset mode.
REF Mode
Whileinthismodeaquickpress
oftheSETbuttonwilltogglethe
displaybetweenabsolute(ABS)
andrelative(REL).
AquickpressoftheMODE
button will exit this mode and
displayeitherABSorRELon
the bottom right corner of the
LCDdependingonwhichone
was chosen.
UNIT Mode
The gage can be changed from inch mode to millimeter mode, or the reverse, with one
quickpushoftheSETbutton.
PRE Mode
ApresetnumbercanbeenteredintothedisplaybyfirstpressingtheSETbutton.
Anegative(-)signwillflashtotheleftofthedigits.Toselectthenegativesignpress
theSETButton.
IfapositivevalueisdesiredpresstheMODEbuttonandthenegativesignwill
disappear(nosignsignifiesapositivevalue)andtheleft-mostdigitwillbegintoflash.
ToincrementthenumberpresstheSETbuttonuntilthedesirednumberisachieved.
Then,usetheMODEbuttontomovetheflashingcharactertothenextdigittothe
right. Continue this procedure until the last digit has been selected.
Hold Feature
WhileintheABSmodeavaluecanbeheld(frozen)inthedisplaybypressingthe
SETbutton.AquickpressoftheSETbuttonwillreactivethedisplaywithnolossof
position.
Output
ThistoolcomeswithanOpto-RS232outputportthatallowsdatatransmissiontoa
variety of peripherals by connecting to a Starrett DataSure
®
Wireless Data Collection
SystemusingaCat.1500-3A-1Nendnode.Connectionthruatraditionalwireisalso
possible.
Print Command
The print command is controlled by the mm/inch button.
Battery Installation
ThecalipercomeswithoneCR20323V
battery installed. To change or install a
new battery refer to Figs. 1 & 2.
First,removetheoutputcover(1)[See
Fig. 1]. Then, remove the battery cover
(2)byslidingitinthedirectionofthe
arrow.
Next,lifttheclearbatteryprotector(3),
oldbattery(4)andbatterygasket(5)out
of the compartment.
Toinstallanewbattery,firstmakesure
thebatterygasketispositionedcorrectlyinthebatterycompartment[SeeFig.2].
(Note:Itisimportantthatthegasketisorientedcorrectlywiththerubberprotrusion
betweenthetwoholesfacingdownward.)Next,placeanewCR2032batteryplus
(+)sideupintothebatterycompartment.Putthe
batteryprotectorbackintopositionontopofthebattery
gasket,againmakingsuretherubbergasketiscorrectly
positioned in the cavity. While lightly pressing down on
thebatteryprotector,slidethebatterycoverbackinto
position over the protector. Finally, insert the output cover
into the output slot located on the top of the cover.
TheLCDnowdisplaysthetwounits-mmandin.Select
thedesiredunitbypressingeithertheMODEbuttonfor
metricmodeortheSETbuttonforinchmode.
Figure 1
Figure 2
Zobrazit stránku 1
1 2

Komentáře k této Příručce

Žádné komentáře